---
title: "Garage Door Won't Close or Reverses | Reno NV"
url: "https://advancedoverheadnv.com/garage-door-wont-close/"
canonical: "https://advancedoverheadnv.com/garage-door-wont-close/"
updated: "2026-11-21"
breadcrumb: "Home > Garage Door Problems > Garage Door Won't Close"
business: "Advanced Overhead Garage Door Company"
what: "garage door repair, broken spring replacement, opener repair and new LiftMaster opener installation, new residential and commercial garage doors, and 24/7 emergency garage door service across the Greater Reno area and Northern Nevada"
phone: "775-356-0444"
phone_2: "775-883-0444"
email: "advohd@yahoo.com"
hours: "Office Mon-Sat 7:30 am-5:00 pm, Sunday closed; Emergency and same-day service available 24/7"
license: "Nevada Lic. No. 61031 (NSCB 0061031A, C-3D Overhead Doors)"
area: "Greater Reno area and Northern Nevada (service-area business)"
offer: "Free estimates"
---

# Garage Door Won't Close

A garage door that stops and reverses before it closes is most often reacting to its photo eyes, the safety sensors near the floor, which are blocked, dirty or out of line. Advanced Overhead Garage Door Company repairs and replaces garage door openers, sensors and wall controls in the Reno area and across Northern Nevada; call 775-356-0444.

The short answer


Safety first

Never hold the wall button down to force a door closed over a fault, and never turn up the opener's force setting. Both defeat the safety reverse that protects people and pets.

Call [775-356-0444](tel:7753560444)

What you may notice

- The door starts down, then goes back up
- The opener lights blink for a few seconds, then nothing happens
- The door closes only while you hold the wall button
- The door stops a few inches above the floor
- The remote works some days and not others, depending on the sun

## Photo eyes: the usual cause

Photo eyes are two small sensors mounted on each side of the door, a few inches off the floor. One sends an invisible beam and the other receives it. If anything breaks the beam, or the receiver cannot see it, the opener will not close the door. The U.S. Consumer Product Safety Commission publication on garage door safety places them 4 to 6 inches above the floor.

Federal safety rules for these openers require the operator to monitor for the presence and correct operation of the sensor at least once during each close cycle, which is why a fault shows up as a refusal to close, not as a door that closes anyway.

## Safe checks before you call

All of these are done with the door open or closed and your hands nowhere near the door's moving parts.

- Look for anything in the beam: a stored box, a leaning broom, a bag, a cobweb or a pet's bed.
- Wipe both sensor lenses with a clean, soft cloth. Dust and moisture can block the beam.
- Check the two indicator lights. Most sensors show a steady light when aligned. A dark or blinking light on one side points to a bump or a bent bracket.
- Gently nudge a sensor back until its light turns steady. Do not bend the bracket hard or loosen the screws that hold the opener.
- Watch for sunlight hitting a lens directly at certain times of day. Shading the sensor with a piece of cardboard for a test will show whether glare is the cause.

If the lights are steady and the door still reverses, run the test in our [safety reversal test guide](https://advancedoverheadnv.com/guides/garage-door-safety-reversal-test/) to see whether the opener reverses on contact. The guide uses a 2x4 on the floor in the door's path, the method the CPSC recommends, and you should repeat it monthly.

## What else can stop a door from closing?

When the sensors are fine, the cause is usually one of the items in the table. Several of them need a technician, because the opener's travel limits and the door's track are involved.

| What you see | Likely cause | What to do |
|---|---|---|
| Sensor light dark or blinking | Wire cut or pinched near the sensor | Look for a damaged wire; call if you find one |
| Door reverses just before the floor | Down-travel limit set too short | Call; the limit setting is part of an opener adjustment |
| Door stops part-way, opener hums | Something in the track, or a bent track | Do not force it; call |
| Opener does not respond to the wall control | Control fault or a wire problem | Check the lock button; see our remotes and keypads page |
| Door crooked, one side lower | Cable or roller problem | Stop using the door; see broken garage door repair |

## Safe checks versus a service call

Cleaning, clearing the beam and gently re-aiming a sensor are fine for a homeowner. Adjusting limit settings, changing force settings, replacing sensor wire or anything touching the door's springs, cables and tracks is work for a technician. DASMA, the Door and Access Systems Manufacturers Association, recommends monthly safety checks and an annual visit from a trained door systems technician.

We repair openers of various brands, and we are an authorized LiftMaster dealer. Our [opener repair](https://advancedoverheadnv.com/garage-door-opener-repair/) service covers sensors, controls and circuit boards, and we give a free estimate. We guarantee all our work.

## Garage Door Won't Close: Questions

### Why does my garage door go down and then back up?

The opener is reversing, which usually means the photo eyes see something in the beam or are out of line. It can also mean the door meets resistance before the floor. Clean and check the sensors first, then call us if it continues.

### Why does the door close only when I hold the button?

Many openers allow a manual close while the button is held when the sensors are not working. It is a sign of a sensor fault, not a fix. Have the sensors and wire checked rather than closing the door this way each day.

### Can sunlight stop a garage door from closing?

Yes. Strong sun shining straight into a sensor lens can confuse it, usually for a short time in the morning or evening. Shading the lens often settles it; if not, a technician can re-aim or relocate the sensor.

### Should I raise the force setting to make it close?

No. A higher force setting can stop the door from reversing when it should, which defeats a safety feature. If the door needs more force to close, something is wrong, and we recommend a call.

[More questions and answers](https://advancedoverheadnv.com/faq/)

### Sources (2)

- U.S. Consumer Product Safety Commission : [cpsc.gov/s3fs-public/garage.pdf](https://www.cpsc.gov/s3fs-public/garage.pdf) (checked November 2026)
- Federal Register : [govinfo.gov/content/pkg/FR-2016-04-07/html/2016-07552.htm](https://www.govinfo.gov/content/pkg/FR-2016-04-07/html/2016-07552.htm) (checked November 2026)
