Nevada Lic. No. 61031

Free EstimateCall Us Today: 775-356-0444

Advanced OverheadGarage Door Company

The Monthly Garage Door Safety Reversal Test

Springs and safety · 6 min read · Updated November 2026

Lay a 2x4 flat on the floor in the door's path, close the door with the opener, and check that it reverses as soon as it touches the board; then block one photo eye with an object over 6 inches tall, press the close button and check that the door does not close. If either test fails, stop using the opener and call a garage door technician such as Advanced Overhead Garage Door Company at 775-356-0444.

Key points

  • Test once a month: the CPSC says to inspect the door and opener every 30 days, and DASMA recommends a monthly test
  • Use a 2x4 laid flat, not a paper-towel roll or a soft object
  • Check the photo eyes too: they sit 4 to 6 inches above the floor
  • A failed test means stop using the opener until it is repaired
  • Never adjust springs, cables or their brackets yourself
Two Advanced Overhead service trucks at a residential job

Why the test matters

An automatic garage door is the heaviest moving object in most homes, and the opener's safety reverse is what stops it from closing on a person, a pet or a car. The U.S. Consumer Product Safety Commission's publication on garage door openers reports that about 73 children between the ages of 2 and 14 have been trapped and killed under automatic garage doors since March 1982 (CPSC Publication 523, revised April 2011).

Federal rules now require entrapment protection on residential openers manufactured on or after January 1, 1993, usually a pair of photo eyes near the floor, and a 2016 update to the rule requires the opener to check that the photo eyes are present and working at least once during each close cycle. Those protections only help if they still work, which is why the test is monthly.

Test 1: the 2x4 reversal test

This checks that the opener reverses when the door meets something solid. The CPSC says to place a 2x4 on the floor of the garage in the door's path, and the door industry association DASMA specifies a 1.5-inch solid object or a 2x4 laid flat.

  1. Open the door fully with the opener.
  2. Lay a 2x4 flat on the floor, centered under the door, where the bottom edge will land.
  3. Close the door with the wall button or remote and stand clear.
  4. Watch the door: it should touch the board, stop and reverse back up within a couple of seconds.
  5. Remove the board and close the door normally.

DASMA explains why a paper-towel roll is the wrong tool: it may not compress to 1.5 inches, so it cannot show that the door reverses when it is almost down. A 2x4 laid flat can.

Test 2: the photo-eye test

The photo eyes are the two small sensors on either side of the door near the floor; CPSC Publication 523 says they should be installed 4 to 6 inches above the floor. LiftMaster's safety check keeps hands away from a moving door: with the door open, block the photo eye with an object over 6 inches tall, then press the opener's close button. The door should not close. Keep children's hands and feet out of the test.

If the door fails either test

Stop using the opener to close the door and call a technician. A door that does not reverse on the 2x4 usually has a closing force or travel setting that needs adjusting, a door that is out of balance, or an opener that is worn out. A door that ignores the photo eyes may have sensors out of line, a damaged wire or an opener too old to support them.

The fix is not always a new opener, but age matters: LiftMaster recommends replacing openers made before 1993 rather than repairing them, because those units predate the federal entrapment rule. We are an authorized LiftMaster dealer; see LiftMaster garage door openers and garage door opener repair.

A monthly look at the rest of the door

While you are there, look at the door without touching the hardware. DASMA recommends monthly safety checks by the owner and an annual visit from a trained door systems technician.

  • Springs: any gap in a coil, or a spring that looks stretched unevenly
  • Cables: fraying, rust or a cable sitting loose on its drum
  • Rollers and hinges: cracked, wobbling or squealing parts
  • Balance: a door that drifts up or slams down when stopped halfway is out of balance
  • Bottom seal: torn or flattened rubber

If you find any of these, do not try to adjust springs, cables or their brackets. Those parts are under high tension. Call us for a tune-up or a repair.

Sources (6)

Related questions

How often should I test my garage door's safety reverse?

Once a month. The CPSC says to inspect the door and the opener every 30 days, and DASMA recommends the reversal test monthly.

Can I use a roll of paper towels instead of a 2x4?

No. DASMA explains that a paper-towel roll may not compress to 1.5 inches, so it cannot show that the door reverses when it is almost down. Use a 2x4 laid flat.

My door reversed on the 2x4 but closes with the photo eye blocked. Why?

The photo eyes may be out of line or failing. Stop closing the door with the opener and call a technician.

Does an old opener need to be replaced if it fails?

Not always, but LiftMaster recommends replacing openers made before 1993 rather than repairing them. We can tell you which applies to yours.

Is the test safe to do myself?

Yes, if you stand clear and keep children and pets away. Leave springs, cables and brackets to a technician.

More questions and answers

Contact Us for Quick Job Quotes and More Information.

Call 775-356-0444 or 775-883-0444, or send the form for a free estimate. Emergency and same-day service available 24/7.